power supply FSP300-60ATV (pf) PC psu replacement power service FSP300-60PFN

道場TOP ネタ一覧 batteryclub2019道場

power supply FSP300-60ATV (pf) PC psu replacement power service FSP300-60PFN

◇評価 0ポイント; ◇閲覧回数 2,764回
◇登録日: 2019年9月24日

: batteryclub2019; 道場主

Lv.25

Maximum transmission power supply replacement - FSP FSP300-60PFN pc power supply 10/5A. FSP300-60PFN power supplies are compatible with all Han power supply FSP300-60ATV (pf). Shopping FSP300-60PFN pc power online, more discount and money-saving. Check your FSP output power and voltage(Ref 80Plus) before you order FSP300-60PFN pc PSU service. Cost-effective computer power supply charging replacement, please visit www.batteryclub.org for more information.

Brand : FSP power supply
Input Voltage : 115-230V
Ouput Volatge : 10/5A
Is there no power supply model you find? Take it easy! Contact us fast with your e-mail for what PC power models your are looking for.

Email: info@batteryclub.org

FSP300-60PFN replacement model：

FSP300-60PFN

Compatiblet with all Han power supply FSP300-60ATV (pf):

For +3.3V +5V +12V1 +12V2 +12V3 -5V -12V +5Vsb
FSP300-60atv(pf) 300W 28A 30A 15A - 0.3A 0.8A 2.0A
FSP350-60GLC 350W 22A 21A 10A 15A - - 0.5A 2.5A
FSP400-60GLC 400W 30A 30A 14A 15A - - 0.5A 2.5A
FSP460-60GLC 460W 30A 30A 16A 18A - - 0.5A 2.5A
FSP500-60GLC 500W 30A 30A 18A 18A - - 0.5A 2.5A
FSP500-60GLN 500W 30A 30A 18A 18A - - 0.5A 2.5A
ambient temperature -20°C~80°C, 5~95% RH
Over-voltage protection: +5V, +3.3V, +12V1, +12V2
Over-current protection +5V, +3.3V, +12V1, +12V2

https://www.batteryclub.org/Goods/FSP17976_SE-FSP300-60PFN-Fsp-Adapter.html

How to maintain FSP FSP300-60PFN computer power supply

1. Remove the fan. Disconnect the main power supply first, and unplug the input and output cables on the back of the power supply. Next, unplug and connect all the accessories connected to the power supply, remove the fixing screws of the power supply box, and take out the power supply box. Observe the appearance of the power supply box, remove the screws reasonably and accurately, and remove the cover. When taking the cover, the wires should be pulled out according to the gap at the same time. Remove the four screws that secure the fan and remove the fan. You can not solder the two power cables temporarily.
2. Clean the dust. After separating the power supply board and the fan with cardboard, use a small brush or a damp cloth to wipe the dust and wipe it clean. It is also possible to use dust from the fan to blow fan blades and bearings.
3. Add lubricant. Peel off the sticker and use a needle-nose pliers to pick out the rubber seal. Find the motor bearing, add lubricant, and when you use the fan to move the fan, make the lubricant flow evenly along the bearing, then add a few drops. Pay attention to whether the fan of the ball bearing has two bearings. Don't neglect the oil feeding to the bearing on the wind side. The oil can't be placed on the main shaft only. Lubricating oils must use computer-specific lubricants or advanced lightweight sewing machine oils. Never use the lubricants used in automobiles. Finally, install the rubber sealing sheet and label it.