TOP > ミュージック > batteryclub2019道場 > ネタ

道場TOP ネタ一覧 batteryclub2019道場

dell 750W power supply replacement E750E-S1

◇評価 0ポイント
◇閲覧回数 973




Maximum transmission power supply replacement - Dell E750E-S1 pc power supply 12.2V==61.47A MAX; +12Vsb==3.0A MAX 750W. E750E-S1 power supplies are compatible with Dell PowerEdge R530 R630 T430 T630 TPJ2X G6W6K. Shopping E750E-S1 pc power online, more discount and money-saving. Check your Dell output power and voltage(Ref 80Plus) before you order E750E-S1 pc PSU service. Cost-effective computer power supply charging replacement, please visit for more information.

  • Brand : Dell power supply
  • Input Voltage : 100-240V~50-60Hz
  • Ouput Volatge : 12.2V==61.47A MAX; +12Vsb==3.0A MAX 750W
    Is there no power supply model you find? Take it easy! Contact us fast with your e-mail for what PC power models your are looking for.


E750E-S1 replacement model:


Compatiblet with Dell PowerEdge R530 R630 T430 T630 TPJ2X G6W6K:

INPUT : 100-240V~50-60Hz
Max AC CURRENT 10.05A-5.0A
OUTPUT : +12.2V==61.47A MAX; +12Vsb==3.0A MAX 750W
MODEL : E750E-S1
REF NO: 700-013536-0000
REV: A01-00
Compatible Models:
DELL PowerEdge R430 R530 R630 R730 R730XD
Dell PowerEdge R530 R630 T430 T630 TPJ2X G6W6K

How to maintain Dell E750E-S1 computer power supply

1. Remove the fan. Disconnect the main power supply first, and unplug the input and output cables on the back of the power supply. Next, unplug and connect all the accessories connected to the power supply, remove the fixing screws of the power supply box, and take out the power supply box. Observe the appearance of the power supply box, remove the screws reasonably and accurately, and remove the cover. When taking the cover, the wires should be pulled out according to the gap at the same time. Remove the four screws that secure the fan and remove the fan. You can not solder the two power cables temporarily.
2. Clean the dust. After separating the power supply board and the fan with cardboard, use a small brush or a damp cloth to wipe the dust and wipe it clean. It is also possible to use dust from the fan to blow fan blades and bearings.
3. Add lubricant. Peel off the sticker and use a needle-nose pliers to pick out the rubber seal. Find the motor bearing, add lubricant, and when you use the fan to move the fan, make the lubricant flow evenly along the bearing, then add a few drops. Pay attention to whether the fan of the ball bearing has two bearings. Don't neglect the oil feeding to the bearing on the wind side. The oil can't be placed on the main shaft only. Lubricating oils must use computer-specific lubricants or advanced lightweight sewing machine oils. Never use the lubricants used in automobiles. Finally, install the rubber sealing sheet and label it.

Here, we provide other products for your reference:

HBC BA225030 2100MAH 6V battery

HBC BA225030 1500mah 6V battery

HBC QD109300 24V ac adapter

HP PCG007 310W power supply

Microsoft G3HTA001H 8030mAh/60.8Wh battery

Lenovo 45N1110 battery 24Wh 11.1V/11.4V

Huawei HB512627ECW battery 410MAH 3.82V

Lenovo L15D1P31 battery 4000mAh 3.8V

Huawei HB442528EBC battery 300MAH 3.8V

CRAFTSMAN CMCB6050 500mah/60V battery

Acer AS16B5J 5600mAh battery

Toshiba PA5173U-1BRS 5200mAh battery

Fujitsu FMVNBP212 2200mAh battery

other products

HP 504966-001 100-240V 50-60Hz 12V

DELL 05NF18 100-240V 10A-5A

HP 403777-001 100-240V~ /4A, 47Hz- 63Hz

Dell HCWV2 100-240V ~/ 4.6A, 50-60Hz

HP 508149-001

HP HP-D3201E0 100-240 V-/5.5A , 50-60 HZ

Dell HP-P3017F3P 100-240V

LENOVO 54Y8861 100-240V``47--63HZ

☆☆☆☆☆ ☆☆☆ ☆

ブログ? そんなの必要ありません! 今日から、いきなりアフィリエイトスタート!